Leading 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.
Leading 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.
Blog Article
Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are lots of mishaps including forklifts.
Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual in front could not be found, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the workers utilized their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which virtually triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.
Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.
Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be slanted backward. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it must follow the web traffic rules in the manufacturing facility and should keep a certain safety and security range from the car ahead. .
7. When the forklift is running, the tons must be in the lowest position that does not hinder the driving, and the gantry needs to be correctly slanted back. The tons will not be elevated other than when piling or packing. .
8. The elevation of the tons should not obstruct the vehicle driver's sight. In special situations, when the product impacts the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is forbidden for workers to base on the fork to hold items and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.
filling and unloading.
1. When fork-loading things, the range in between the two forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the lots, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet discharge.
Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you must discharge the goods or reduced the fork structure.
2. Pull the hand brake take care of to dead or dispirit the hand Electric Forklift Truck for Warehouse brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should also be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop Stand-on Electric Pallet Stacker the tendency of "free switching";.
6. Running up and down the incline should be slow and uniform, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into big or hefty goods and most likely to the driver's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844